Hold the wider side of the safety cap, squeeze, and pull at the same time.

There are three methods of application:

FAST-2-3min:

Apply InstantBond adhesive on one side on its own as a super adhesive, bring parts together, and hold tightly or clamp. The Accelerator is not necessary if time is not a factor. Curing time without accelerator 2- 5 minutes (environment dependent) for an incredibly strong bond.

FASTER-Alignment Method:

Apply InstantBond adhesive on one side to be bonded and align the pieces together until you feel for best position, then spray the accelerator around the outside of the joints, this will start the acceleration of the curing process from the outside in, give this process a little more time to cure.  (20-30 seconds)

FASTEST-Most commonly used Fastest method:

For the FASTEST bonding time, apply InstantBond adhesive on one side and spray the accelerator onto the joining side, (Please note you will not be able to align parts once they touch) bring them together and hold FIRMLY for a few seconds. (For an even faster cure apply the accelerator to both sides) bonded 2-3 seconds

The main characteristic of InstantBond adhesive is that it cures instantly on demand with the use of the accelerator thus eliminating the use of clamping devices or hold-down methods. Our claim is the “no hold” freedom which offers new possibilities in the repair, installation, and/or building methods that were not available before. Its most important attribute is that it’s not only an extremely strong and versatile adhesive but cures instantly on demand, with the introduction of an innovative aerosol accelerator agent. It creates a new experience of instant repairs and installation never before possible. The new freedom of a ‘no hold’ ‘No Wait’ philosophy is what really sets it apart InstantBond from all other adhesive products. Hence “Everything else is just glue”

Amazing speed and strength with InstantBond. No need to wait for messy products to dry. InstantBond instantly bonds wood, stone, plastic, glass, metals, ceramics, etc. Note, please practice on scrap pieces before final use.

Yes, you can use InstantBond without the accelerator if time is not a factor, you can slow down the curing time by not using the accelerator and depending on the materials used, the curing time without the use of the accelerator is 5 to 8 minutes. The accelerator is used only when you need to cure immediately or hold parts in place instantly. If time is not a factor than just use the adhesive alone. In most cases use the accelerator to cure the adhesion just so it reduces the chance of getting the adhesive on your hands or other parts.

Yes, when you want to be more precise or prevent aerosol accelerator overspray, spray the accelerator into the cover cap, the liquid will quickly accumulate at the bottom of the cup, then use a clean cloth to dip into the liquid and wipe the area that needs to be glued and/or activated. This method provides for more precise and accurate placement of the Accelerator and prevents overspray of the accelerator on any unwanted area of concern.

Yes, to thicken the adhesive for overhead applications or non-runny applications, simply store the adhesive bottle in the refrigerator. It will turn to a gel-like thickness. For a thinner adhesive, place the bottle under warm running water until the desired thickness is achieved.

To normalize the adhesive, store it at room temperature.

*TIP: Storing Inoteca Instantbond adhesive at a colder temperature such as in a fridge or even in a freezer, will lengthen the shelf life, please make sure to seal it tight before storing.

Yes, Inoteca Instantbond will certainly hold the part in place while the Silicone or PL adhesive cures. Use a little bit of InstantBond (the size of a dime) as a hold down on all the corners and spray the accelerator on the opposite side.  Use construction-grade all-weather Silicone or PL adhesive as the major adhesive.  Place the part and hold it down for several seconds, flattening out the silicone at the same time.  This method will permit you to apply the adhesives without the use of hold-down clamps or tape, and walk away because the InstantBond will hold the sign in place while the silicone sets.

Shelf life is greatly dependent on room temperature and humidity. The higher the temperature and humidity the shorter the shelf life. At normal 70 degrees shelf life should be approx. 18 to 24 months. Shelf life can be dramatically lengthened by storing the adhesive in your refrigerator or indefinitely in the freezer.

Yes, and InstantBond will dry faster as well. Whereas contact cement has to be applied on the surface and wait for 15 minutes to be able to stick something on it and up to a few hours to completely dry, InstantBond will only take 2 minutes to initially bond and will be completely dry in 8 minutes. With the Accelerator the process is much faster, and after 5 seconds the bond will be completely dry. In either case, InstantBond dries much faster and much stronger than contact cement.